April 21, 2015

Matls. IM 209

Supersedes October 21, 2014

Appendix D

AGGREGATE GRADATION TABLE – ENGLISH

 

Grad. No.

 

Section No.

 

Std. Sieve Size

 

1½”

 

 

3/4”

 

1/2”

 

3/8”

 

#4

 

#8

 

#30

 

#50

 

#100

 

#200

 

 

Intended Use

Percent Passing

*Notes

1

4110,4125, 4133

PCC FA Cover Agg.

 

 

 

 

100

90-100

70-100

10-60

 

 

0-1.5

1

2

4112

PCC Intermediate

 

 

 

95-100

 

 

0-10

 

 

 

 

 

3

4115 (57, 2-8), 4118

PCC CA

100

95-100

 

25-60

 

0-10

0-5

 

 

 

0-1.5

2,10

4

4115 (2-8)

PCC CA

100

50-100

30-100

20-75

5-55

0-10

0-5

 

 

 

0-1.5

10

5

4115 (67, 2-8)

PCC CA

 

100

90-100

 

20-55

0-10

0-5

 

 

 

0-1.5

10

6

4115.05

(Repair & Overlay)

 

PCC CA

 

 

 

100

 

90-100

 

40-90

 

0-30

 

 

 

 

 

0-1.5

 

10

7

4117 (Class V)

PCC FA & CA

100

 

 

 

 

80-92

60-75

20-40

 

 

 

 

8

4117.03 (Class V)

Fine Limestone

 

 

 

 

100

90-100

 

 

 

 

0-30

 

10

4120.02, 4120.03, 4119

(C Gravel)

 

Granular Surface

 

 

 

100

 

 

 

50-80

 

25-60

 

 

 

 

 

3, 11

11

4120.02, 4120.04,

4120.05, 4120.07, 4119

(A, B, Cr. St.)

Granular Surface & Shoulder

 

 

100

 

95-100

 

70-90

 

 

30-55

 

15-40

 

 

 

 

6-16

 

4, 5, 11

12a

4121 (Cr. St.)

Granular Subbase

100

 

 

40-80

 

 

5-25

 

 

 

0-6

6, 11

12b

4121 (Cr. Gravel)

Granular Subbase

100

 

 

50-80

 

 

10-30

 

5-15

 

3-7

7, 11

13

4122.02 (Cr. St.)

Macadam St. Base

3” nominal maximum size – screened over 3/4” or 1” screen

 

14

4123

Modified Subbase

100

 

70-90

 

 

 

10-40

 

 

 

3-10

5, 7, 11

19

4125 (1/2” Cr. Gr.

or Cr. St.)

 

Cover Aggregate

 

 

 

100

 

97-100

 

40-90

 

0-30

 

0-15

 

 

 

 

0-1.5

 

11

20

4125 (1/2” Scr. Gr.)

Cover Aggregate

 

 

100

95-100

40-80

0-15

0-7

 

 

 

0-1.5

11

21

4125 (3/8”)

Cover Aggregate

 

 

 

100

90-100

10-55

0-20

0-7

 

 

0-1.5

11

22

4124.02

Fine Slurry Mixture

 

 

 

 

100

85-100

40-95

20-60

14-35

10-25

5-25

9, 11

23

4124.02 (Cr. St.)

Coarse Slurry Mixture

 

 

 

 

 

100

 

70-90

 

40-70

 

19-42

 

 

 

 

 

5-15

 

11

29

4131

Porous Backfill

 

 

100

95-100

50-100

0-50

0-8

 

 

 

 

11

30

4132.02 (Cr. St.)

Special Backfill

100

 

 

 

 

 

 

10-40

 

 

 

0-10

5, 11

31

4132.03 (Gravel)

Special Backfill

 

100

90-100

75-100

 

 

30-55

 

 

 

3-7

11

32

4133 (Sand/Gr./Cr. St.)

Granular Backfill

                            100% passing the 3” screen

10-100

 

 

 

0-10

8, 11

35

4134 (Natural Sand/Gr.)

Floodable Backfill

100

 

 

 

 

 

20-90

 

 

 

0-4

11

36

4134 (Natural Sand)

Floodable Backfill

 

 

 

 

 

100

 

 

 

 

0-2

11

 

Notes: (Gradations Nos. 9, 15, 16, 17, 18, 24, 25, 26, 27, 28, 33 and 34 have been deleted.)

 

1.      For Section 4110, when the fine aggregate is sieved through the following numbered sieves -  4, 8, 16, 30, 50, and 100 -  not more than 40% shall pass one sieve and be retained on the sieve with the next higher number.

 

2.        When used in precast and prestressed concrete bridge beams, 100% shall pass the 1” sieve. When used for pipe bedding the No. 200 restriction does not apply.

 

3.      When compaction of material is a specification requirement, the minimum percent passing the No. 200 sieve is 6%. When used as trench backfill, must be a minimum 75% crushed gravel.

 

4.      See specifications for combination of gravel and limestone.

 

5.      Unwashed air-dried samples of crushed composite material shall be tested for gradation compliance except that no gradation determination will be made for material passing the No. 200 sieve.

 

6.      The gradation requirement for the No. 8 sieve shall be 5% to 20% when recycled material is supplied.

 

7.      For Section 4121 gravel, one fractured face on 30% or more of the particles retained on the 3/8-inch sieve.  For Section 4123 gravel, one fractured face on 75% or more of the particles retained on the 3/8-inch sieve.

 

8.      Crushed stone shall have 100% passing the 1.5” sieve.

 

9.      Gradation limitations for the 30, 50 and 100 sieves shall not apply when slurry mixture is applied by hand lutes, such as for slurry leveling.

 

10.    Maximum of 2.5% passing the No. 200 sieve allowed for crushed limestone or dolomite when documented production is 1% or less..

 

11.    When Producer gradation test results are used for acceptance, test results representing at least 90% of the material being produced shall be within the gradation limits and the average of all gradation results shall be within the gradations limits. Stockpiled material not meeting the criteria may, at the District Materials Engineer’s discretion, be resampled using Materials I.M. 301 procedures. One hundred percent of the stockpile quality control and verification test results shall be within the gradation limits.